Materials
Mild steel, stainless steel or aluminium to specification.

Rack & Electronics Components
Rack shelves, blanking panels and rack accessories made to your rack interface.
Manufacturing scope
Shelves and blanking panels are cut and formed to your rack interface, with ventilation patterns and fixing slots produced from the approved drawing.
Illustrative geometry; final design follows your approved drawing.Technical review
Mild steel, stainless steel or aluminium to specification.
Laser cutting of vent patterns and slots, with CNC bending of flanges and returns.
Mounting patterns, overall dimensions, ventilation cutouts and edge finish.
Typical customers: Rack makers and electronics integrators.
Rack interfaces, shelf loading and any thermal or electrical requirements must be specified. Electronic systems and performance testing are separate.
Related products
Product data
Rack shelves, blanking panels and rack accessories are folded to the 19-inch interface and your depth, with vents and mounting slots cut to drawing.
Used in
1U – 4U, plain or vented
Front-mount or four-post
With telescopic slides
Brush and finger panels
| Thickness | 1.2 – 2 mm typical |
|---|---|
| Interface | EIA-310 / IEC 60297 19-inch |
| Laser cutting | MS up to 20 mm · SS up to 12 mm · Al / Cu up to 6 mm |
| Max bend length | 3200 mm on 100 t, five-axis CNC (LVD-YSD PPES 1032) |
| Finish | Deburring, grinding, polishing in-house; powder coat, plating or PVD through approved suppliers |
| Inspection | Dimensions checked against your drawing revision before dispatch |
| Order size | Prototype, pilot and repeat batches |
Carbon steel
IS 513 (CR1–CR4) · DC01–DC04
Smooth cold-rolled surface for painted or powder-coated parts. The usual choice for enclosures, covers and brackets.
| Tensile strength | 270 – 410 MPa |
|---|---|
| Yield strength | ≤ 280 MPa (grade dependent) |
| Elongation | 28 – 38 % |
| Hardness | ≈ 50 – 65 HRB |
| Density | 7.85 g/cm³ |
|---|---|
| Melting range | 1450 – 1520 °C |
| Thermal conductivity | ≈ 50 W/m·K |
| Elastic modulus | 200 GPa |
Coated carbon steel
IS 277 · coating Z120 – Z275
Pre-galvanised sheet for trays, ducts and covers that need corrosion protection without painting.
| Tensile strength | ≈ 270 – 500 MPa (base grade) |
|---|---|
| Yield strength | ≈ 180 – 350 MPa |
| Elongation | ≥ 22 % |
| Zinc coating | 120 – 275 g/m² (both sides) |
| Density | 7.85 g/cm³ |
|---|---|
| Zinc melting point | 420 °C |
| Thermal conductivity | ≈ 50 W/m·K |
| Elastic modulus | 200 GPa |
Aluminium alloy
ASTM B209 · EN AW-5052
Bends well and resists corrosion. The usual aluminium for formed housings, chassis and panels.
| Tensile strength | 215 – 265 MPa |
|---|---|
| Yield strength | ≥ 160 MPa |
| Elongation | 7 – 12 % |
| Hardness | ≈ 60 HB |
| Density | 2.68 g/cm³ |
|---|---|
| Melting range | 607 – 649 °C |
| Thermal conductivity | 138 W/m·K |
| Elastic modulus | 70 GPa |
Austenitic stainless
ASTM A240 · EN 1.4301
General-purpose stainless with good corrosion resistance and weldability. Non-magnetic when annealed.
| Tensile strength | ≥ 515 MPa |
|---|---|
| Yield strength (0.2 %) | ≥ 205 MPa |
| Elongation | ≥ 40 % |
| Hardness | ≤ 92 HRB |
| Density | 8.00 g/cm³ |
|---|---|
| Melting range | 1400 – 1450 °C |
| Thermal conductivity | 16.2 W/m·K |
| Elastic modulus | 193 GPa |
Typical published values for the grade. Actual values follow the mill test certificate of the supplied lot.
| Rack units | Panel height | Notes |
|---|---|---|
| 1U | 44.45 mm (panel 43.7 mm) | Blanking / vented panel |
| 2U | 88.9 mm (panel 88.1 mm) | Shelf or panel |
| 3U | 133.35 mm (panel 132.5 mm) | Panel or sub-rack |
| 4U | 177.8 mm (panel 177 mm) | Panel or chassis |
| Panel width | 482.6 mm (19 in) | Mounting pitch 465 mm |
Rack depth and rail positions follow your drawing.
Questions
Common choices are CRCA mild steel, Galvanised steel (GI / GP), Aluminium 5052-H32, Stainless steel 304. Other grades are quoted on request.
Flat blanks up to 1500 x 3000 mm from one sheet and bends up to 3200 mm long on a 100-ton, five-axis CNC press brake. Larger parts are made in welded or bolted sections.
Yes. We make prototypes and first-off samples for approval, then repeat batches from the recorded setups.
A drawing (DXF, DWG, STEP or PDF) with its revision, the material grade and thickness, quantity, finish and delivery date. A STEP file helps for bent and welded parts.
Quick quote
Share the basics now. We follow up for the drawing and any details we need.
Quote checklist
Tap what you already have
Share the drawing, material, quantity, finish and delivery date. We review it and reply with a quotation for prototypes or repeat batches.
Your privacy choices
We use necessary storage to run this site and remember your choices. With your consent we also use Google analytics and marketing tags to understand how the site is used, and load the Google Maps location map. These can set cookies. You can change this any time under “Cookie settings”. Privacy policy
Vinay Metal
Sales team · replies on WhatsAppContinue on WhatsApp
Scan with your phone camera. WhatsApp opens with your message ready to send to Daksh Shah.
Open WhatsApp