Materials
Mild steel, stainless steel and aluminium; finish to the application.

Machine Covers & Housings
Machine cladding, covers and access doors formed to your equipment layout.
Manufacturing scope
Cladding panels and access doors are fabricated around your machine frame, with cutouts, return bends and fixing points taken from the approved drawing.
Illustrative geometry; final design follows your approved drawing.Technical review
Mild steel, stainless steel and aluminium; finish to the application.
Laser cutting of panels and cutouts, CNC bending of return flanges, welding or fastened construction.
Panel alignment, gaps, hinge and latch positions, mounting interfaces and visible surfaces.
Typical customers: Packaging, process-equipment and automation manufacturers.
Safety-related guards require customer-approved design, clearances and risk assessment. Fabrication alone does not establish machine safety compliance.
Related products
Product data
Machine cladding, covers and access doors are formed to your equipment layout so panels fit the frame, open where operators need access and close cleanly.
Used in
Bolted to frame
With handles and locks
Lift-off or quarter-turn fixings
Large formed panels
| Thickness | 1 – 3 mm typical |
|---|---|
| Laser cutting | MS up to 20 mm · SS up to 12 mm · Al / Cu up to 6 mm |
| Max bend length | 3200 mm on 100 t, five-axis CNC (LVD-YSD PPES 1032) |
| Welding | Laser welding: MS 6 mm · SS 5 mm · Al 3 mm; TIG / arc for heavier joints |
| Finish | Deburring, grinding, polishing in-house; powder coat, plating or PVD through approved suppliers |
| Inspection | Dimensions checked against your drawing revision before dispatch |
| Order size | Prototype, pilot and repeat batches |
Carbon steel
IS 513 (CR1–CR4) · DC01–DC04
Smooth cold-rolled surface for painted or powder-coated parts. The usual choice for enclosures, covers and brackets.
| Tensile strength | 270 – 410 MPa |
|---|---|
| Yield strength | ≤ 280 MPa (grade dependent) |
| Elongation | 28 – 38 % |
| Hardness | ≈ 50 – 65 HRB |
| Density | 7.85 g/cm³ |
|---|---|
| Melting range | 1450 – 1520 °C |
| Thermal conductivity | ≈ 50 W/m·K |
| Elastic modulus | 200 GPa |
Coated carbon steel
IS 277 · coating Z120 – Z275
Pre-galvanised sheet for trays, ducts and covers that need corrosion protection without painting.
| Tensile strength | ≈ 270 – 500 MPa (base grade) |
|---|---|
| Yield strength | ≈ 180 – 350 MPa |
| Elongation | ≥ 22 % |
| Zinc coating | 120 – 275 g/m² (both sides) |
| Density | 7.85 g/cm³ |
|---|---|
| Zinc melting point | 420 °C |
| Thermal conductivity | ≈ 50 W/m·K |
| Elastic modulus | 200 GPa |
Austenitic stainless
ASTM A240 · EN 1.4301
General-purpose stainless with good corrosion resistance and weldability. Non-magnetic when annealed.
| Tensile strength | ≥ 515 MPa |
|---|---|
| Yield strength (0.2 %) | ≥ 205 MPa |
| Elongation | ≥ 40 % |
| Hardness | ≤ 92 HRB |
| Density | 8.00 g/cm³ |
|---|---|
| Melting range | 1400 – 1450 °C |
| Thermal conductivity | 16.2 W/m·K |
| Elastic modulus | 193 GPa |
Ferritic stainless
ASTM A240 · EN 1.4016
Magnetic, cost-effective stainless for indoor panels, trims and appliance parts.
| Tensile strength | ≥ 450 MPa |
|---|---|
| Yield strength (0.2 %) | ≥ 205 MPa |
| Elongation | ≥ 22 % |
| Hardness | ≤ 89 HRB |
| Density | 7.75 g/cm³ |
|---|---|
| Melting range | 1425 – 1510 °C |
| Thermal conductivity | 26.1 W/m·K |
| Elastic modulus | 200 GPa |
Aluminium alloy
ASTM B209 · EN AW-5052
Bends well and resists corrosion. The usual aluminium for formed housings, chassis and panels.
| Tensile strength | 215 – 265 MPa |
|---|---|
| Yield strength | ≥ 160 MPa |
| Elongation | 7 – 12 % |
| Hardness | ≈ 60 HB |
| Density | 2.68 g/cm³ |
|---|---|
| Melting range | 607 – 649 °C |
| Thermal conductivity | 138 W/m·K |
| Elastic modulus | 70 GPa |
Typical published values for the grade. Actual values follow the mill test certificate of the supplied lot.
Questions
Yes, from your drawing or a dimensioned sketch. We review bend allowances, hinge and fastener positions before cutting.
Mostly CRCA mild steel for powder-coated covers, and stainless steel 304 or aluminium where hygiene or weight matters.
A drawing (DXF, DWG, STEP or PDF) with its revision, the material grade and thickness, quantity, finish and delivery date. A STEP file helps for bent and welded parts.
Quick quote
Share the basics now. We follow up for the drawing and any details we need.
Quote checklist
Tap what you already have
Share the drawing, material, quantity, finish and delivery date. We review it and reply with a quotation for prototypes or repeat batches.
Your privacy choices
We use necessary storage to run this site and remember your choices. With your consent we also use Google analytics and marketing tags to understand how the site is used, and load the Google Maps location map. These can set cookies. You can change this any time under “Cookie settings”. Privacy policy
Vinay Metal
Sales team · replies on WhatsAppContinue on WhatsApp
Scan with your phone camera. WhatsApp opens with your message ready to send to Daksh Shah.
Open WhatsApp