Materials
Mild steel, SS 304 / 316 and aluminium as specified.

Electrical Enclosures
Gland plates and mounting plates cut and formed to your hole pattern.
Manufacturing scope
Gland plates and component mounting plates are a practical first order: hole patterns, cutouts and folded edges are produced to your drawing in repeat batches.
Design example; final design follows your approved drawing.Technical review
Mild steel, SS 304 / 316 and aluminium as specified.
Laser cutting of hole patterns and profiles, with CNC bending for folded edges where required.
Hole sizes and positions, flatness, edge finish and fit to the enclosure.
Typical customers: Panel builders and enclosure manufacturers.
Scope covers mechanical fabrication. Electrical fit-out, IP ratings and other approvals require a separately agreed specification and verification.
Related products
Custom junction box bodies, covers and mounting plates made to your drawing.
View pageFabricated control panel and cabinet bodies, doors and internal partitions.
View pageSee the full product family and its manufacturing scope.
View pageProduct data
Gland plates and mounting plates are laser-cut flat with every hole, slot and knockout positioned from your drawing, then formed with return flanges where stiffness is needed.
Used in
Blank plates for site drilling
Gland holes cut to your cable schedule
Flat or flanged, with tapped or clinched fixings
Two-piece plates for pre-terminated cables
| Thickness | 1.5 – 3 mm (gland), 2 – 3 mm (mounting) |
|---|---|
| Gland hole sizes | M16 – M63 and PG patterns as specified |
| Laser cutting | MS up to 20 mm · SS up to 12 mm · Al / Cu up to 6 mm |
| Max bend length | 3200 mm on 100 t, five-axis CNC (LVD-YSD PPES 1032) |
| Flatness | Checked on the surface table against drawing |
| Finish | Deburring, grinding, polishing in-house; powder coat, plating or PVD through approved suppliers |
| Inspection | Dimensions checked against your drawing revision before dispatch |
| Order size | Prototype, pilot and repeat batches |
Carbon steel
IS 513 (CR1–CR4) · DC01–DC04
Smooth cold-rolled surface for painted or powder-coated parts. The usual choice for enclosures, covers and brackets.
| Tensile strength | 270 – 410 MPa |
|---|---|
| Yield strength | ≤ 280 MPa (grade dependent) |
| Elongation | 28 – 38 % |
| Hardness | ≈ 50 – 65 HRB |
| Density | 7.85 g/cm³ |
|---|---|
| Melting range | 1450 – 1520 °C |
| Thermal conductivity | ≈ 50 W/m·K |
| Elastic modulus | 200 GPa |
Coated carbon steel
IS 277 · coating Z120 – Z275
Pre-galvanised sheet for trays, ducts and covers that need corrosion protection without painting.
| Tensile strength | ≈ 270 – 500 MPa (base grade) |
|---|---|
| Yield strength | ≈ 180 – 350 MPa |
| Elongation | ≥ 22 % |
| Zinc coating | 120 – 275 g/m² (both sides) |
| Density | 7.85 g/cm³ |
|---|---|
| Zinc melting point | 420 °C |
| Thermal conductivity | ≈ 50 W/m·K |
| Elastic modulus | 200 GPa |
Austenitic stainless
ASTM A240 · EN 1.4301
General-purpose stainless with good corrosion resistance and weldability. Non-magnetic when annealed.
| Tensile strength | ≥ 515 MPa |
|---|---|
| Yield strength (0.2 %) | ≥ 205 MPa |
| Elongation | ≥ 40 % |
| Hardness | ≤ 92 HRB |
| Density | 8.00 g/cm³ |
|---|---|
| Melting range | 1400 – 1450 °C |
| Thermal conductivity | 16.2 W/m·K |
| Elastic modulus | 193 GPa |
Aluminium alloy
ASTM B209 · EN AW-5052
Bends well and resists corrosion. The usual aluminium for formed housings, chassis and panels.
| Tensile strength | 215 – 265 MPa |
|---|---|
| Yield strength | ≥ 160 MPa |
| Elongation | 7 – 12 % |
| Hardness | ≈ 60 HB |
| Density | 2.68 g/cm³ |
|---|---|
| Melting range | 607 – 649 °C |
| Thermal conductivity | 138 W/m·K |
| Elastic modulus | 70 GPa |
Copper alloy
IS 410 · CuZn37 (C27200)
Decorative and electrical parts. Laser-cutting thickness is confirmed per job.
| Tensile strength | ≈ 340 – 450 MPa |
|---|---|
| Yield strength | ≈ 150 – 350 MPa |
| Elongation | ≈ 10 – 50 % |
| Hardness | ≈ 60 – 120 HV |
| Density | 8.44 g/cm³ |
|---|---|
| Melting range | 900 – 920 °C |
| Thermal conductivity | ≈ 120 W/m·K |
| Elastic modulus | ≈ 105 GPa |
Typical published values for the grade. Actual values follow the mill test certificate of the supplied lot.
| Gland size | Clearance hole | Notes |
|---|---|---|
| M16 | 16.5 mm | |
| M20 | 20.5 mm | |
| M25 | 25.5 mm | |
| M32 | 32.5 mm | |
| M40 | 40.5 mm | |
| M50 | 50.5 mm | |
| M63 | 63.5 mm |
Clearance values are typical; we cut the hole size shown on your drawing.
Questions
Gland plates are cut on our fibre laser from your hole pattern, so repeat plates can be made in batches once the drawing is approved. Lead time is confirmed with each quotation.
Mild steel up to 20 mm, stainless steel up to 12 mm and aluminium or copper up to 6 mm. Most mounting plates are 2 to 3 mm.
Yes. Gland plates can be made in CRCA, galvanised steel, stainless steel, aluminium or brass to suit the panel and cable glands.
A drawing (DXF, DWG, STEP or PDF) with its revision, the material grade and thickness, quantity, finish and delivery date. A STEP file helps for bent and welded parts.
Quick quote
Share the basics now. We follow up for the drawing and any details we need.
Quote checklist
Tap what you already have
Share the drawing, material, quantity, finish and delivery date. We review it and reply with a quotation for prototypes or repeat batches.
Your privacy choices
We use necessary storage to run this site and remember your choices. With your consent we also use Google analytics and marketing tags to understand how the site is used, and load the Google Maps location map. These can set cookies. You can change this any time under “Cookie settings”. Privacy policy
Vinay Metal
Sales team · replies on WhatsAppContinue on WhatsApp
Scan with your phone camera. WhatsApp opens with your message ready to send to Daksh Shah.
Open WhatsApp